Durability to resist wind and reinforce with preventive corrosion steel. Moreover, Q-CON is No Knocking Sound and can hang 50 kg per point by Expansion fixing.
Reduced working time and transportation cost due to Light weight (70 kg/m2). Furthermore, Q-CON is good heat insulation AAC panel (K=0.115 w/mk.) to save Energy as well.
Excellent Fire resistance as Q-CON is Non- Combustible material and can protect fire for 4 hours.
Q-CON Wall Panel is environmental friendly material due to Non-toxic that made from natural components and Reduce waste.
W x L x H (cm.)
|60 x 300 x 7.5||70||10|
|60 x 300 x 10||100||7|
Q-CON Wall Panels are lightweight, steel reinforced, groove & tongue panels that can be easily installed by your normal on-site installers. They are suitable to be used as both external and internal walls.
Q-CON Wall Panel Passed BS5234 Standard Guaranteed … Trusted Partition for your project!!!
Q-CON wall panel can help you to finish job faster than brick & mortar up to 3 times and easily install by groove and tongue panel.
Q-Con Wall Panel is steel reinforced start from 7.5 cm. thickness and available in lengths of 1.50 – 4.0 m. and width of 0.6 – 3.0 m.
Dimension, Weight and Packaging:
W x L x H (cm.) Weight Packaging
60x300x7.5 53 kg/sq.m. 8 Pcs/Pallet
60x300x10 70 kg/sq.m. 6 Pcs/Pallet
Preventive corrosion steel reinforce Q-Con Wall Panel too durable so it is difficult cracking even if facing wind load, lifting during construction or hanging heavy stuff.
Load Bearing Wall: Support the weight of hanging load 50
Q-CON Wall Panel is renowned for its highly fire resistant properties, it works as fire resistance insulation as same as AAC block, it can help to protect you better in the case of a fire.
As be an autoclaved lightweight concrete (ALC), Q-Con Wall Panel can save not only budget cost but energy consumption also.
Q-Con Wall Panel are manufactured in a range of sizes to suit, resulting in less wastage. Moreover, it made from completely natural materials which is not pollution causes.
1. Check sizes and quantities of Q con wall panel.
2. Check layout and construction drawing.
3. Check tools and equipment.
1. Clean and Mark the wall alignment. Clean the floor and ceiling without dust or dirt before making the line by the chalk tape.
2. Clean Q-Con Wall Panel and move to the marked point.
3. Mix thin-bed mortar and apply it on structure. Apply mix thin bed mortar on column structure for increase adhesion between the Q-con wall panel and the structure.
4. Lift the wall panel and push it to attach the column.
5. Insert a foam sheet between floor and top of the panel.Foam sheets prevent wall cracking from slab defection effect.
6. Use lever to lift Q-con wall panel until top of the panel reach the upper floor then insert a wood wedge under the panel.
7. Use steel angle to fasten the panel with floors on both upper and lower side of the panel by using steel plugs and screws.
8. Apply thin-bed mortar on side of the first panel then lift the next wall panel to attach and do the same as the previous steps.
9. Continue install wall panels until the gap can be closed by the last panel.
10. Measure the gap and cut the last panel to fit in then install it in place.
11. Fill the gap under the panels with sand-cement mortar for fill the gap under wall panel.
12. Fill all gaps between each panel with thin-bed mortar, wait until the mortar dry then rub with sandpaper #400.
13. Finishing all gaps again with skim coat then rub with sandpaper #200.
14. Finish Q-con wall panel installation. Can finish the surface with painting or as required.
Central Pattana Public Company Limited or CPN who is owner and operate many shopping centers under three brands; centralwOrld, CentralPlaza, and CentralFestival, office building, hotel, residential and condominium project.
It is pleasure of SCG to be a partner who get the trustiness from CPN to support wall application solution like Q-CON Wall Panel to many shopping centers such as centralwOrld, CentralPlaza Chaengwattana, CentralPlaza Lardprao and CentralPlaza Chonburi.
The outstanding property that make the leader company in Thailand confident in Q-CON Wall Panel is super speed install. Q-CON installation is faster than brick and mortar 4 times
CPN gets several benefits from using Q-CON not only saving time but other hidden advantages also.
|Product Property||Wall Panel||Standard|
|Dry Density||550-650 Kg/m3||IS – 2185 (Part III)|
|Working Density||600-700 Kg/m3|
|Wind Load||50-180 Kg/m2|
|Compressive Strength||>4 N/mm2||IS2185(partIII)|
|Water Absorption||<33%||by mass|
|Fire Rating||Up to 4 hr||100mm. thickness wall panel / BS476 Part 20 and 22 :1987|
|Thermal Conductivity (k)||0.115 W/mk|
|Sound Insulation (STC)||38 - 43 dB|
|Reinforce steel tensile strength||> 500 N/mm2|
|Weight||70 kg/m2||100 mm thickness wall panel|
Subscribe to receive update news and every trends about construction in INDIA